Optimization of culture medium to improve bio-cementation effect based on response surface method.

The main challenge in the large-scale application of MICP lies in its low efficiency and promoting biofilm growth can effectively address this problem. In the present study, a prediction model was proposed using the response surface method. With the prediction model, optimum concentrations of nutrients in the medium can be obtained. Moreover, the optimized medium was compared with other media via bio-cementation tests. The results show that this prediction model was accurate and effective, and the predicted results were close to the measured results. By using the prediction model, the optimized culture media was determined (20.0 g/l yeast extract, 10.0 g/l polypeptone, 5.0 g/l ammonium sulfate, and 10.0 g/l NaCl). Furthermore, the optimized medium significantly promoted the growth of biofilm compared to other media. In the medium, the effect of polypeptone on biofilm growth was smaller than the effect of yeast extract and increasing the concentration of polypeptone was not beneficial in promoting biofilm growth. In addition, the sand column solidified with the optimized medium had the highest strength and the largest calcium carbonate contents. The prediction model represents a platform technology that leverages culture medium to impart novel sensing, adjustive, and responsive multifunctionality to structural materials in the civil engineering and material engineering fields.

Identification and extraction of cementation patterns in sand modified by MICP: New insights at the pore scale.

Microbially induced calcium carbonate precipitation (MICP) is an environmentally friendly technology that improves soil permeability resistance through biocementation. In this study, 2D microscopic analysis and 3D volume reconstruction were performed on river sand after 24 cycles of bio-treatment based on stacked images and computed tomography (CT) scanning data, respectively, to extract biocementation patterns between particles. Based on the mutual validation findings of the two techniques, three patterns in the biocemented sand were identified as G-C-G, G-C, and G-G. Specifically, 2D microscopic analysis showed that G-C-G featured multi-particle encapsulation and bridging, with a pore filling ratio of 81.2%; G-C was characterized by locally coated particle layers, with a pore filling ratio of 19.7%; and the G-G was marked by sporadic filling of interparticle pores, with a pore filling ratio of 11.7%. G-C-G had the best cementation effect and permeability resistance (effective sealing rate of 68.5%), whereas G-C (effective sealing rate of 2.4%) had a relatively minor contribution to pore-filling and flow sealing. 3D volume reconstruction showed that G-C-G had the highest pore filling rate, followed by G-G and G-C. The average filling ratios of area and volume for G-C-G were 83.979% and 77.257%, respectively; for G-G 20.360% and 23.600%; and for G-C 11.545% and 11.250%. The analysis of the representative element volume (REV) was conducted, and the feasibility and reliability of the micro-scale pattern extraction results were confirmed to guide the analysis of macro-scale characteristics. The exploration of the effectiveness of cementation patterns in fluid sealing provides valuable insights into effective biocementation at the pore scale of porous media, which may inspire future research.

Comparison of osteolysis around 3 different cement restrictors in total hip arthroplasty.

BACKGROUND AND AIM: Several studies reported osteolysis around polyethylene glycol/polybutylene terephthalate (PEG/PBT) based femoral cement restrictors. Our goal was to evaluate and compare osteolysis around 3 different plug designs: the slow biodegradable PEG/PBT cement restrictor; the fast biodegradable gelatin cement restrictor; and the non-biodegradable polyethylene plug. PATIENTS AND METHODS: In a retrospective multicentre cohort study chart data were extracted of patients who received a total hip arthroplasty between 2008 and 2012. A total of 961 hips were included. Cortical ratio between inner and outer cortices at the centre of the plug was measured on routine postoperative follow-up moments. Median follow up of all 3 hospitals was 3.5 years (1.4-7.3). The primary outcome was evidence of osteolysis (i.e. the difference in cortical ratio [CR]) on anteroposterior (AP) radiographs at final follow-up. RESULTS: Progressive osteolysis was found around the PEG/PBT cement restrictor represented by a significantly increasing cortical ratio (ΔCR 0.067 (95% CI, 0.063-0.071). Distance from tip prosthesis to plug and size of the plug were found to be independent factors in predicting increased cortical ratio. CONCLUSIONS: Our multicentre cohort shows increase of cortical ratio around the PEG/PBT cement restrictor which progresses over time. Physicians should be aware of this fact and are advised to intensify follow-up of patients who received this cement restrictor.

[Cement in revision arthroplasty-what about the "glacier effect"? : Case studies viewed from different perspectives]. / Zement in der Revisionsendoprothetik ­ Was ist mit dem "Gletschereffekt"? : Fallbeispiele aus unterschiedlichen Perspektiven betrachtet.

BACKGROUND: The number of operations concerning revision arthroplasty has been increasing continuously in recent years, and it can be assumed that they will continue to increase in the future. If an arthroplasty implant becomes loose, it must be changed. The question often arises as to how the new implant should be fixed in the bone. ADVANTAGES: Revision implants can be inserted into the bone without cement. In the subsequent period, a secondary osseointegration of the implant takes place. Another possibility is to anchor the implant by using bone cement. The advantage of cemented anchorage is that the implant is firmly fixed in the bone, in principle, immediately, and it is possible to fully load the implant directly. Direct postoperative full weight bearing is helpful, especially for older and multimorbid patients, in order to achieve rapid mobilization. PREREQUISITES AND CHALLENGES: When using cement in revision cases, however, there are a few prerequisites and challenges that the surgeon should definitely take into account. In the case of revision, the bone in the former implant bed is often deficient and appears thinned and sclerosed. It is, therefore, important to analyze the bone quality preoperatively on radiographic images and to include it in the planning of the anchoring strategy. In addition, the individual bone quality of the patient must also be taken into account intraoperatively. In any case, it must be clarified whether the basic prerequisites for the sufficient bond strength of the cement with the bone to be formed can still be met. Furthermore, the principles of cementing technique must be strictly observed, and the goal of a perfect cement mantle must be aimed for. If the indication for this is overstated, early loosening of the cemented revision arthroplasty is very likely.

Effect of a modified laminate veneer preparation design on absolute margin discrepancy and marginal overhang.

STATEMENT OF PROBLEM: Veneer preparation designs impact veneer accuracy. However, whether a modified design could reduce absolute margin discrepancy and marginal overhangs is unclear. PURPOSE: The purpose of this in vitro study was to investigate whether a modified veneer preparation design enhances the absolute margin discrepancy and marginal overhang. MATERIAL AND METHODS: The absolute margin discrepancy and the marginal overhang of 3 different veneer preparation designs on a typodont tooth (n=20): feather edge, shoulder, and shoulder with wings were measured. The feather edge design was prepared first and subsequently modified to create the shoulder and shoulder with wings preparations. Ceramic veneers were fabricated using computer-aided design and computer-aided manufacture with each veneer assessed for fit before cementation. Ten specimens were cut vertically, and 10 were cut horizontally in each group. The absolute margin discrepancy and marginal overhangs were measured for each cross-section with scanning electron microscopy. Descriptive data analysis and hypothesis testing were conducted using the nonparametric Kruskal Wallis test (α=.05). RESULTS: On the vertical sections, the shoulder with wings preparation had the best absolute margin discrepancy and overhang. The design was also best for mesial overhang and mesial absolute margin discrepancy when measuring horizontally. CONCLUSIONS: The shoulder with wings preparation design produced the smallest cervical absolute margin discrepancy and overhang. This design also produced absolute margin discrepancy and overhangs comparable with those of the shoulder design in the proximal areas.

Formulations of NaOCl-based in liquid, gel form or with surfactants on dentin deproteinization before fiber post cementation.

The objective of the study was to evaluate the effects of dentin deproteinization protocols for post space using different formulations containing sodium hypochlorite before fiber post cementation with self-adhesive resinous cement. The groups were divided according to the irrigation protocol (DWC, SHS, SHT and SHG). The residue cleanliness, bond strength, adhesive failure pattern, and tag formation at the adhesive interface between the self-adhesive cement and the dentin were evaluated. For this, analysis in scanning electron microscope, push-out test and confocal laser scanning microscopy were performed. The SHT protocol showed the highest residue cleanliness on the dentin surface of the post space (p<0.05). In addition, SHT protocol showed highest bond strength and tag formation in the cervical and middle thirds (p<0.05). Dentin deproteinization with sodium hypochlorite with surfactant provided the best dentin cleaning of residues, bond strength and tag formation after cementation of the fiber post with self-adhesive cement.

Influence of using different translucent composite resins for customizing fiber post on the bond strength of self-adhesive cement to root dentin.

This study evaluated the influence of different translucent resins (Z350 and Opallis) for customizing fiber posts and light-curing the cementation system using different LED equipment (V, Valo or R, Radii-Cal) on the bond strength and adhesive failure pattern at 24 h and 6 months. Eighty roots were prepared and divided into 4 groups (n=20): ZV (Z350 resin and LED Valo), ZR (Z350 resin and LED Radii-Cal), OV (Opallis resin and LED Valo), OR (Opallis resin and LED Radii-Cal). After post space preparation, the fiber post was customized and cemented with self-adhesive cement and light-curing using V or R LED equipment. Bond strength values were submitted to 2-way ANOVA test. ZV and ZR showed higher bond strength values than the other groups at 6 months of evaluation (p<0.05). The Z350 resin has a favorable influence on the bond strength of self-adhesive cement to root dentin, regardless of the LED polymerization equipment used.

Effect of clinical and laboratory techniques of cementation on the assessment of marginal and internal fit of prosthetic elements

Aim: The aim of this in vitro study was to compare machine and manual cementation of prosthetic elements by measuring internal and marginal fits. Methods: Eighteen anatomic prefabricated abutments were used to manufacture zirconia copings in the Ceramill (n=9) and Lava systems (n=9). The copings were cemented with a fluid consistency addition silicone using a machine (n=18) and manually (n=18) according to the replica technique. They were then cut in the buccal-palatal and mesial-distal directions. The film thickness was photographed using an optical microscope and measured in the internal and marginal regions. The data collected were analyzed by repeated measures ANOVA and Bonferroni's multiple comparison test (∂=.05). The Bland-Altman test was performed to evaluate the agreement between the methods. Results: In the evaluation of the internal and marginal misfits, the mean values observed for the cementation performed with the aid of a machine and manually, were as follows: angular regions, 76.7 µm and 76.2 µm; linear regions, 60.6 µm and 60.7 µm; incisal region, 144.8 µm and 145.2 µm; marginal region, 40.1 µm and 40.2 µm; and overall mean, 80.4 µm and 80.6 µm, respectively. No significant differences were found between the 2 methods, for any of regions and systems (P>.05). The Bland-Altman test showed agreement between the methods (P>.05) and that the limits of agreement found were clinically acceptable. Conclusions: Within the limitations of this in vitro study, we can conclude that cementation using manual techniques or mechanical aid produces the same cement films

Influence of cement type, excess removal, and polishing on the cement joint.

OBJECTIVES: To compare marginal gap width and depth with different cementation systems, excess removal, and after polishing. METHOD AND MATERIALS: In total, 80 composite crowns were milled, divided into ten groups, and cemented on identical artificial teeth. Eight crowns per group were fixed with (i) zinc phosphate cement (ZnOPh), (ii) glass-ionomer cement (GIC), (iii) resin-reinforced glass-ionomer cement (GIC mod), (iv) dual-curing adhesive composite (Comp dual), or (v) dual-curing self-adhesive composite (Comp SE dual). Excess removal was performed with a scaler after brief light-cure (tack-cure), final light-cure, during rubber or gel phase or by wiping with foam pellet. Curing was completed in chemical, dark cure, or light-curing modus. The specimens were polished and stored in water (37°C). The margins were digitized using a 3D laser-scanning microscope (VK-X100 series, Keyence). The width and the depth of the marginal gap were measured at 10 points between the crown margin and the preparation margin. RESULTS: The width after excess removal varied between 65.1 ± 15.7 µm (Comp dual, wipe, with polishing) and 208.6 ± 266.7 µm (Comp SE dual, dark cure, without polishing). The depth varied between 29.8 ± 22.2 µm (Comp dual, wipe, with polishing) and 89.5 ± 45.2 µm (Comp SE dual, dark cure, without polishing). The impact on gap width and depth was detected for fixation material, excess removal, and polishing. CONCLUSION: The gap depth and width depend on the luting material and the mode of access removal. Polishing can improve the gap quality, especially for GIC and resin-based systems.

Properties and mechanisms of steel slag strengthening microbial cementation of cyanide tailings.

The advantages of microbial induced carbonate precipitation (MICP) as bio-cementation technology for tailings-solidification are under extensive investigation. In order to improve performance of bio-cementation, many strengthening materials were applied to the bio-cementation of tailings. Steel slag (SS) is a kind of industrial solid waste, its chemical composition and mineral composition are similar to cement, and it has a certain application prospect as an auxiliary cementing material. In this study, the properties and mechanism of SS strengthening MICP cementation of cyanide tailings (CT) were investigated. The results showed that Sporosarcina pasteurii growth is not inhibited by SS, and Sporosarcina pasteurii can promote the hydration reaction of SS, providing a suitable alkaline environment and Ca2+, promoting the production of more CaCO3 in the MICP process. When 200 mL of CT leachate was added 1.4 g SS (200-400 mesh), the adsorption of Cu, Pb, Zn, Cd, total cyanide (T-CN), and free cyanide (F-CN) reached 48.05%, 44.28%, 36.25%, 16.67%, 79.05%, and 67.20%, respectively. The maximum unconfined compressive strength（UCS） of the cemented body (with 5%, 150 mesh SS) was 1.97 MPa, which was 3.396 times as high as that without SS. The cemented body with the addition of SS (5%, 150 mesh) contained more carbonate bound Cu (2.75%), Pb (4.89%), Zn (5.37%), and Cd (5.75%), and less exchangeable Cu (3.65%), Pb (6.85%), Zn (2.27%), and Cd (4.42%) than that without SS. In summary, the addition of SS improved the UCS of cemented bodies and the stability of heavy metals and cyanide, reduced the environmental risks existing in the process of CT storage. Meanwhile, it also provides new ideas for resource utilization of industrial solid waste SS and improvement of mine filling materials.

An in vitro study measuring marginal gaps of inlay restorations fabricated from different CAD-CAM materials after thermocycling.

BACKGROUND: Many monolithic machined materials have been introduced and provided a suitable mechanical and physical properties for inlay restorations. However, there is shortage in the studies evaluating the marginal adaptation using these materials. PURPOSE: This study aimed to compare the effect of fabricating inlay restorations from 3 different CAD-CAM materials on marginal gaps before and after thermocycling. MATERIALS AND METHODS: Sixty human premolars were randomly divided into 3 groups (n = 20) according to the material used: (e.max CAD, Ivoclar AG, Schaan, Liechtenstein), (HC, Shofu, Koyoto, Japan) and (Brilliant Crios, Coltene, Altstätten, Switzerland) (n = 20). A scanning electron microscope (SEM) (JSM- 6510 lv, JEOL, Tokyo, JAPAN) was used to for measuring the marginal gaps after cementation of inlay restorations. The magnification was adapted to 250x. Marginal gaps were revaluated with SEM after thermocycling. The temperatures of baths were 5 and 55 °C was applied for a total of 5000 cycles. All data were statistically analyzed by using ANCOVA to demonstrate if there were any statistically significant differences between the gap measures after thermocycling of the three independent (unrelated) groups. A Bonferroni adjustmen was used to perform post hoc analysis (α = 0.05). RESULTS: Post-intervention marginal gap was statistically significantly lower in group EX (110.8 µm) which was statistically significant compared with group SF (112.5 µm) (mean difference=-1.768, P = .007) and group BR (113 µm) (mean difference=-2.272, P = .001), however, in. comparing SF and BR groups, there was no significant difference (mean difference=-0.5, P = .770). CONCLUSIONS: Thermocycling affected the marginal gaps of composite based restoration and resin-modified ceramics widely. However, it had a very small effect on glass ceramics marginal adaptation. CLINICAL IMPLICATIONS: The marginal gaps of CAD-CAM inlays varied according to material used (ceramic based, combination, or resin based). Thermocycling has a minor effect on the marginal adaptation of lithium disilicate glass-ceramic inlays, where it affected the margin of resin-modified ceramic and composite based inlays greatly. Using lithium disilicate glass-ceramic might improve the clinical longevity of inlay restored teeth.

Ablación tumoral y cementación en el tratamiento de las metástasis vertebrales. Estudio multicéntrico / Tumor ablation and vertebral augmentation in the treatment of vertebral metastases: A multicenter study

Introducción: El tratamiento de las fracturas vertebrales metastásicas sin compresión neural se realiza con técnicas percutáneas de cementación. El aumento de presión intratumoral por estas técnicas puede enviar células tumorales al torrente sanguíneo. Para evitar esa diseminación y mejorar el tratamiento del dolor se han introducido las técnicas de ablación que permitirían crear una cavidad en el tumor previo a la cementación o directamente necrosar la metástasis cuando el tamaño es pequeño. Material: Presentamos la experiencia con la ablación de dos hospitales y dos técnicas de ablación distintas. El primer grupo usó la ablación por radiofrecuencia (ARF) en 14 pacientes (26 vértebras) de los cuales en cuatro se asoció una artrodesis vertebral. El segundo grupo usó la ablación por microondas (AMO); 93 pacientes (129 lesiones) sin asociar instrumentación vertebral. Resultados: En el grupo de ARF la mejoría del dolor en la escala visual analógica (EVA) fue de 7,7 a 2,6 a las seis semanas. No hubo complicaciones derivadas de la ablación. En la mayoría de los casos se asoció la cementación. En el grupo de AMO la mejoría del dolor en EVA pasó de 6,8 a 1,7 a las seis semanas. En todos los casos se asoció la cementación. No hubo complicaciones derivadas de la ablación. Conclusiones: La asociación de las técnicas de ablación a la cementación vertebral es una técnica segura, que permite mejorar notablemente el dolor del paciente y puede ayudar al control de la enfermedad.(AU)

Introduction: Treatment of metastatic vertebral fractures without neural compression is performed with percutaneous cementation techniques. The increase in intratumoral pressure by these techniques can send tumor cells into the bloodstream. To prevent this dissemination and improve pain treatment, ablation techniques have been introduced that would allow the creation of a cavity in the tumor prior to cementation or directly necrosing the metastasis when its size is small. Material: We present the experience with ablation of two hospitals and two different ablation techniques. The first group used radiofrequency ablation (A) in 14 patients (26 vertebrae), 4 of whom underwent vertebral arthrodesis. The second group used microwave ablation (B) in 93 patients (129 lesions) without associated vertebral instrumentation. Results: In group A pain improvement in VAS was 7.7–2.6 at 6 weeks. There were no complications derived from the ablation. In most cases cementation was associated. In the group B pain improvement in VAS went from 6.8–1.7 at 6 weeks. Cementation was associated in all cases. There were no complications derived from the ablation. Conclusion: The association of ablation techniques with vertebral cementation is a safe technique that significantly improves the patient's pain and can help control the disease.(AU)

[Translated article] Tumor ablation and vertebral augmentation in the treatment of vertebral metastases: A multicenter study / Ablación tumoral y cementación en el tratamiento de las metástasis vertebrales. Estudio multicéntrico

Introducción: El tratamiento de las fracturas vertebrales metastásicas sin compresión neural se realiza con técnicas percutáneas de cementación. El aumento de presión intratumoral por estas técnicas puede enviar células tumorales al torrente sanguíneo. Para evitar esa diseminación y mejorar el tratamiento del dolor se han introducido las técnicas de ablación que permitirían crear una cavidad en el tumor previo a la cementación o directamente necrosar la metástasis cuando el tamaño es pequeño. Material: Presentamos la experiencia con la ablación de dos hospitales y dos técnicas de ablación distintas. El primer grupo usó la ablación por radiofrecuencia (ARF) en 14 pacientes (26 vértebras) de los cuales en cuatro se asoció una artrodesis vertebral. El segundo grupo usó la ablación por microondas (AMO); 93 pacientes (129 lesiones) sin asociar instrumentación vertebral. Resultados: En el grupo de ARF la mejoría del dolor en la escala visual analógica (EVA) fue de 7,7 a 2,6 a las seis semanas. No hubo complicaciones derivadas de la ablación. En la mayoría de los casos se asoció la cementación. En el grupo de AMO la mejoría del dolor en EVA pasó de 6,8 a 1,7 a las seis semanas. En todos los casos se asoció la cementación. No hubo complicaciones derivadas de la ablación. Conclusiones: La asociación de las técnicas de ablación a la cementación vertebral es una técnica segura, que permite mejorar notablemente el dolor del paciente y puede ayudar al control de la enfermedad.(AU)

Introduction: Treatment of metastatic vertebral fractures without neural compression is performed with percutaneous cementation techniques. The increase in intratumoral pressure by these techniques can send tumor cells into the bloodstream. To prevent this dissemination and improve pain treatment, ablation techniques have been introduced that would allow the creation of a cavity in the tumor prior to cementation or directly necrosing the metastasis when its size is small. Material: We present the experience with ablation of two hospitals and two different ablation techniques. The first group used radiofrequency ablation (A) in 14 patients (26 vertebrae), 4 of whom underwent vertebral arthrodesis. The second group used microwave ablation (B) in 93 patients (129 lesions) without associated vertebral instrumentation. Results: In group A pain improvement in VAS was 7.7–2.6 at 6 weeks. There were no complications derived from the ablation. In most cases cementation was associated. In the group B pain improvement in VAS went from 6.8–1.7 at 6 weeks. Cementation was associated in all cases. There were no complications derived from the ablation. Conclusion: The association of ablation techniques with vertebral cementation is a safe technique that significantly improves the patient's pain and can help control the disease.(AU)

MDP-salts as an adhesion promoter with MDP-primers and self-adhesive resin cement for zirconia cementation.

PURPOSE: To evaluate the effect of zirconia priming with MDP-Salt before MDP containing primers and self-adhesive cement on the shear bond strength. MATERIALS AND METHODS: Fully sintered high translucent zirconia specimens (n = 120) were assigned into 2 groups (n = 60 each): Control (No Pretreatment) and Methacryloyloxydecyl dihydrogen phosphate salt (MDP-Salt) pretreated. Each group was divided into 3 subgroups (n = 20) according to cementation protocol: 1) MDP + Silane primer and conventional resin cement, 2) MDP+ Bisphenyl dimethacrylate (BPDM) primer and conventional resin cement, and 3) MDP containing self-adhesive resin cement. Shear bond strength (SBS) was measured after 10,000 thermocycling. Contact angle was measured for tested groups. Surface topography was assessed using a 3D confocal laser scanning microscope (CLSM). Weibull analysis was performed for SBS and one-way ANOVA for contact angle and surface topography measurements (α = 0.05). RESULTS: The use of MDP-Salt significantly improved the SBS (p < .05) for all tested subgroups. Self-adhesive cement showed an insignificant difference with MDP + Silane group for both groups (p > .05). MDP + BPDM showed a significantly lower characteristic strength compared to self-adhesive resin cement when both were pretreated with MDP-Salt. No difference between all tested groups in the surface topographic measurements while MDP-Salt showed the highest contact angle. CONCLUSION: MDP-Salt pretreatment can improve bonding performance between zirconia and MDP containing products.

Clinical Performance of Minimally Invasive Monolithic Ultratranslucent Zirconia Veneers: A Case Series up to Five Years of Follow-up.

There is a lack of reports in the literature on the long-term clinical performance of ultratranslucent zirconia, especially considering its use in manufacturing monolithic veneers. The purpose of this case series is to describe the aesthetic treatment steps of three patients with minimally invasive ultratranslucent zirconia veneers and to report the clinical findings up to five years. Three patients (woman: 2, man: 1; mean age: 30 years) unsatisfied with their dental aesthetics sought dental treatment. The treatment plan involved cementing ultratranslucent zirconia veneers. Air-abrasion was performed on the internal surface of zirconia with alumina particles coated by silica (silicatization), followed by silane and adhesive applications for the adhesive cementation. All veneers were adhesively cemented to enamel with resin cement (Variolink Esthetic, Ivoclar). The patients were clinically evaluated annually considering the Ryge modified/ California Dental Association criteria. After a mean follow-up of 4.33 years (4-5 years), a survival rate of 100% was detected for the 28 minimally invasive ultratranslucent zirconia veneers cemented in the 3 patients. There were no absolute failures such as debonding, veneer fracture, or secondary caries. Superficial marginal discoloration was observed in one element (maxillary left lateral incisor) of one patient. Ultratranslucent zirconia is a viable option for manufacturing veneers due to its excellent clinical performance and longevity. However, further long-term clinical studies are essential to consolidate this material as an option for esthetic restorations.

The load capacity of maxillary central incisor with simulated flared root canal restored with different fiber-reinforced composite post and cementation protocols.

Background: This study aimed to evaluate the load capacity of maxillary central incisors with simulated flared root canal restored with different fiber-reinforced composite (FRC) post cemented with either self-adhesive or self-etch resin cement and its mode of fracture. Methods: Sixty-five extracted maxillary incisors were decoronated, its canal was artificially flared and randomly categorized into group tFRC (tapered FRC post) (n = 22), mFRC (multi-FRC post) (n = 21), and DIS-FRC (direct individually shaped-FRC (DIS-FRC) post) (n = 22), which were further subdivided based on cementation resin. The posts were cemented and a standardized resin core was constructed. After thermocycling, the samples were loaded statically and the maximum load was recorded. Results: The load capacity of the maxillary central incisor was influenced by the different FRC post system and not the resin cement (p = 0.289), and no significant interaction was found between them. Group mFRC (522.9N) yielded a significantly higher load capacity compared to DIS-FRC (421.1N). Overall, a 55% favorable fracture pattern was observed, and this was not statistically significant. Conclusion: Within the limitation of the study, it can be concluded that prefabricated FRC posts outperform DIS-FRC posts in terms of the load capacity of a maxillary central incisor with a simulated flared root canal. The cementation methods whether a self-adhesive or self-etch resin cement, was not demonstrated to influence the load capacity of a maxillary central incisor with a flared root canal. There were no significant differences between the favorable and non-favorable fracture when FRC post systems were used to restored a maxillary central incisor with a flared root canal.

[The third-generation modern cementing technique in hip and knee arthroplasty]. / Moderne Zementiertechnik der dritten Generation in der Knie- und Hüftendoprothetik.

BACKGROUND: Implant loosening is the most common reason for revision surgery. OBJECTIVES: Contribution of modern cementing technique to the long-term stability of an implant. METHODS: Evaluation of the available evidence on modern cementing technique. RESULTS: Modern cementing technique in hip arthroplasty is considered established and leads to better cementing results. In knee arthroplasty, there are also specific recommendations, including intensive cleaning of the bone bed, mixing of bone cement under vacuum and application of bone cement to the implant and the bone. CONCLUSIONS: The use of modern cementing technique in hip and knee arthroplasty facilitates cementing, increases safety, and minimizes the risk of mechanical loosening.

Luting laminate veneers: Do resin-composites produce less polymerization stress than resin cements?

OBJECTIVES: Regular composites could produce less polymerization stress than resin cements when luting laminate veneers but there is no proper evidence to support this theory. The current study aimed to determine the degree of conversion, volumetric shrinkage, polymerization stress and the resultant elastic moduli of materials currently used for adhesive cementation and to determine possible correlations. METHODS: The study considered (i) regular resin composites (Admira Fusion, Gradia, Grandioso, Palfique, Sirius Z, Viscalor and Z100) at room and pre-warmed (PW) at 69ºC, (ii) flowable composites (Sigma Flow and Grandioso Flow); (iii) solely light-activated cements (AllCem Veneer, Variolink Esthetic and RelyX Veneer); and (iv) one dual-activated resin cement (SpeedCEM). Degree of conversion (DC, n = 3) was accessed with FTIR 1 h after irradiation. Bonded-disk and Bioman II instruments were used to access polymerization shrinkage strain and shrinkage stress, respectively, for 60 min at 23 ± 1◦C (n = 3). The elastic modulus was determined by 3-point bending flexural test (n = 6). The results were submitted to analyse s of variance, Tukey's, and correlation tests. RESULTS: For regular composites, the pre-warming did not affect DC, shrinkage and modulus but significantly increased the stress magnitude. Correlation tests indicated a significant relationship only between stress and polymerization shrinkage (r = 0.811343). SIGNIFICANCE: Regular composites can produce less polymerization stress than resin cements when luting laminate veneers. Polymerization stress was dependent on the shrinkage magnitude, but not on the degree of conversion nor the elastic modulus.

The effect of defect size and location on the fracture risk of proximal tibia, following tumor curettage and cementation: An in-silico investigation.

Even though, proximal tibia is a common site of giant cell tumor and bone fractures, following tumor removal, nonetheless very little attention has been paid to affecting factors on the fracture risk. Here, nonlinear voxel-based finite element models based on computed tomography images were developed to predict bone fracture load with defects with different sizes, which were located in the medial, lateral, anterior, and posterior region of the proximal tibia. Critical defect size was identified using One-sample t-test to assess if the mean difference between the bone strength for a defect size was significantly different from the intact bone strength. Then, the defects larger than critical size were reconstructed with cement and the mechanics of the bone-cement interface (BCI) was investigated to find the regions prone to separation at BCI. A significant increase in fracture risk was observed for the defects larger than 20 mm, which were located in the medial, lateral and anterior regions, and defects larger than 25 mm for those located in the posterior region of the proximal tibia. Furthermore, it was found that the highest and lowest fracture risks were associated with defects located in the medial and posterior regions, respectively, highlighting the importance of selecting the initial location of a cortical window for tumor removal by the surgeon. The results of the BCI analysis showed that the location and size of the cement had a direct impact on the extent of damage and its distribution. Identification of critical regions susceptible to separation at BCI, can provide critical comments to surgeons in selecting the optimal cement augmentation technique, which may ultimately prevent unnecessary surgical intervention, such as using screws and pins.

Effect of sodium hypochlorite-based formulations on the adhesion interface after fiber post cementation.

The study evaluated the persistence of residues, bond strength and tags formation of a cementation system after post-space irrigation with different sodium hypochlorite-based irrigants. The groups were divided according to the irrigation protocol (DW: distilled water; SHS: sodium hypochlorite solution; SHG: sodium hypochlorite gel; and, SHT: sodium hypochlorite with surfactant). Forty roots (n=10) were used to evaluate the persistence of residues by scanning electron microscopy. Other forty roots were used to the push-out bond strength test, failure mode and tag formation analyses. Non-parametric data were submitted to Kruskal Wallis and Dunn tests, while parametric data were evaluated by one-way ANOVA. No difference was observed in the persistence of residues. DW showed the highest bond strength and tag formation. Type 2 failure mode was the most frequent in the experimental groups. Compared to control, SHT showed the best performance, since less negative effects on adhesive interface was observed.